Алтернативни енергоизточници > Toroidal Power Unit - Steven Mark
Otto`s TPU experiments
Радeв:
Translation to Bulgarian language:
Здравей Ото!
Аз съм пробвал повечето ти схеми на TPU. Те не работят като TPU, те са просто паралелен LC трептящ кръг. Капацитета се съдържа в транзисторите (и обратните диоди вградени в тях).
Когато ползвам ферит и 12V постоянно захрамващо напрежение при резонансната честота имам КПД около 0.7 - 0.9. Получават се кратки импулси с голям размах - около 600 - 700V(това е повредило осцилоскопа ти и другото ти обурудване). Повечето осцилоскопи поддържат до 300V пик до пик с 10 МегаОма сонда. Аз измервам напреженията през грец от бързи диоди и през филтров кондензатор. Ползвайки импулсния трансформатор от компютърно захранване преобразувах високите напрежения в напрежения 70-80V, но тока е много малък.
Проблема не е в конструкцията на намотките на TPU-то, ами в електронната схема и правилните честоти (неслучайно то е патентовано, за разлика от констукцията на намотките). Имам 4 снимки (с пддобрено качество от официалните демонстрационни видеота) на прототипа на TPU-то на Стивън Марк, от lz1co (той има подобни резултати на моите с твойта конфигурация на намотките):
Аз мисля, че правилния начин са високите честоти (около 100-200MHz). Вижте TPU-то на Стивън Марк, че съдържа намотки с малко намотки => се използват високи честоти.
В момента нямам генератор на високи честоти.
Ото, с цялото ми уважение, но мисля че ти си избрал герешен път за реализация на TPU,
otto:
Hello all,
@Radko,
yes youre right. If we look at the open TPU we can see 22 turns of lamp wire wound over a core. We dont know whats the core material.
I have to say that Im using a Metglas core and I dont think the people can buy such a core.
In the past I made every week 1 TPU. Some of them workig good, others not so good.....always missing something.
A long time ago I realized that the coils are NOT sooo important. Everything "around" a TPU is important: the way of pulsating, the feedback, the mechanical construction.....a lot of factors are involved.
I dont agree with using higher frequencies. We know the frequencies: 245kHz and 35kHz and they are OK.
Hmmm... every single TPU will have his frequency because every builded TPU will have different coil lenghts, circumference....So, this 2 frequencies are only as a guide.
Let us discuss something else: SM used tubes. We know why but we dont know HOW!!!
I want to start a discussion how a tube works, that a tube is better then a MOSFET.....we know this.
I want a discussion about how SM connected a tube to a TPU. Maybe you have an idea?? And after we figure that out we can discuss how to replace a tube with a MOSFET. What property has a tube and the MOSFET not?
Otto
mzk:
Tubes are faster than a MOSFET?
And can attain higher frequencies maybe. I mean lower DTC and sharpen pulses.
I don't know why nobody discuss the radiant energy prerequisites -> high frequency, sharp pulses, only one pole (e.g. AC will not work here).
I have a friend who has done successful experiments with two car ignition coils (wireless electricity transmission). He has not measured the COP right now, but this type of transmission has no Lenz effect.
As far as I know, these are not EM (electromagnetic) waves, but some other sort (electrostatic or electrogravitational waves !)
PS: Otto, I agree with your last considerations about the coil-form. I mean it may be really important that the coil form is non-linear (eg. cone, pancake or something else).
MarioBros:
Ако ще ползвате MOSFET транзистори за по висока честота, трябват ви специални схеми на управление на гейта.
Входния капацитет на мощните MOSFET транзистори е 1-5 нанофарада и управляващия ток способен да запуши и отпуши транзистора е от порядка на 2-4 Ампера.
TC4420CP е схема специално разработена за случая с изход до 6А. http://pdf1.alldatasheet.com/datasheet-pdf/view/75053/MICROCHIP/TC4420CPA.html
Продава се в Комет
http://home.comet.bg/shop/index.html
Не бива с писането на английски за което се извиняавм на автора.
Sorry, I can't write in english.
For hi frecuency MOSFET transistors need more curency to drive the Gate about 2-4 Ampers.
otto:
Hello all,
Im here again after a long time.
Maybe you should look into the Steven Marks thread and see how I solved the TPU problem.
The name of the thread is "Steven Marks secret".
Have fun and USE my informations.
Otto
Навигация
[0] Списък на темите
Премини на пълна версия