Алтернативни енергоизточници > MEG, INKOMP, комутатори на магнитни потоци, магнитни усилватели

Експерименти с комутатор на магнитни потоци (КМП)

<< < (33/61) > >>

nali2001:
Thanks Sheki and Getca!

Does he say anything how exactly he is pulsing the system?

To me it seems he is Dc pulsing the systems with a very short duty cycle, and there seems to be a tuned capacitor that 'produces' the rest of the Ac since wave. But actually doing that procedure is in reality not that simple, especially in the higher power ranges... The timing of the Dc pulse must be dead accurate and must happen in the right 'moment' of the sine wave. In other words it is not easy to get the pulse to happen exactly after the top of the sinewave. So I was hoping he maybe explained some of the in the video.

Thanks!
Regards,
Steven

getca:
Hi again, Steven,

Unfortunatelly, Mr.Ivanov doesn't explain how the control coils are pulsed, but I know he uses a half sine wave of the input AC voltage. There is a parallel resonant control circuit and the current flows only when the input voltage exceeds the resonant one through a power diode. About DC pulsing I don't know...
On the video the inventor demonstrates a device with 5kW max. output power. He measured about 1200W output and COP=2.06.

Wish You success...

nali2001:
"long" ago there was on the Inkomp page a slide show which showed a few oscilloscope screenshots. Its was on this page now they are gone... They provided good info, but I was so stupid and only saved two of them. So are there any people out here who have all the original oscilloscope screenshots? I really would like to see them again...

(Maybe someone could post this request in Bulgarian so everyone here can read it?)

This is what the pictures showed:
01 - control pulses without load
 51, 52 - unloaded generator input current
 53, 54 - loaded generator input current???
 55, 56 - unloaded generator input voltage
 57, 58 - unloaded generator input voltage

 59, 60 - control pulses with load

 65 - standard resistor for measuring current of control pulses 1 Ohm/75W
 62, 63 - control pulses current when applying load
 48, 49 - control pulses without load
 66 - output voltage with load

Kind regards,
Steven

varvarin:
Здравейте отново

Иване, доколкото разбирам от писаното от теб и картинките на трансформатора ти насищаш магнитопровода с потока от постоянния магнит а управляващите намотки извеждат магнитопровода от зоната на насищане. В патента на Бардън не се препоръчва насищане но там се има предвид насищане чрез намотките. Никъде обаче не е споменато че постоянния магнит трябва да насити магнитопровода. Така или иначе неодимовите магнити насищат еднакво добре и ферит от ТХО и магнитопрвод от METGLAS. Да разбирам ли че това е ключът към успеха с МЕГА на Бардън, защото моите предишни експерименти водеха само до получаване на импулсен трансформатор, който работи по един и същ начин с магнит и без магнит?

ivan_simeonov:
Здравейте колеги
Да ама не, тия дни ми подариха един железен магнитопровод, такъв като в оригиналната схема на мег, веднага намотах тела, останах като гръмнат, КОП = 4.8!!!!!!!!!!!
има нещо тука.... стоя и се чеша умно по главата, но факт, работи много по добре от ферита и то при много грубо изпълнение, но иска много повече магнити за да заработи, не знам дали това не е причината, по голям магнит повече енергия
Вие до къде стигнахте
Поздрави

Навигация

[0] Списък на темите

[#] Следваща страница

[*] Предходна страница

Премини на пълна версия