Автор Тема: Хладилникът на Айнщайн (Einstein refrigerator)  (Прочетена 8528 пъти)

Неактивен sbk1

  • Подготвен
  • **
  • Публикации: 198
    • sgcar.hit.bg
Една забравена разработка на Алберт Айнщайн (U.S. Patent 1,781,541) възродиха учени от Университета в Оксфорд. Става въпрос за хладилник, който работи без електричество. Съвременните хладилни съоръжения имат изключително неблагоприятно отражение върху околната среда. Те работят чрез компресиране на създадени от човека газове (фреони), с мощно парниково действие, надвишаващо в пъти това на СО2. А с повишаването на стандарта на живот в страните от третия свят производството и продажбите на хладилници непрекъснато растат в последните години.

В хладилника на Айнщтайн и Szilard се ползва смес от амоняк, бутан и вода, като се ползва свойството на течностите при по-ниско налягане да кипят при по-ниска температура. От едната страна е изпарителят – съд, съдържащ бутан. При намаляване на налягането се снижава температурата му на кипене и като се изпарява, той понижава околната температура.

McCulloch възнамерява да осъвремени дизайна, като замени вида на ползваните газове и така да се стигне до четирикратно увеличение на ефективността. Енергия отвън ще бъде нужна единствено за задвижване на помпата и това вероятно в съвременния вариант ще бъде осъществено с помощта на соларни панели.

http://en.wikipedia.org/wiki/Einstein_refrigerator - в енциклопедията
http://www.me.gatech.edu/energy/andy_phd/ - Design Analysis of the Einstein Refrigeration Cycle
Според някои съвременни изследователи на тази идея, КПД се движи между 0,13 и 0,4.

Цитат
Starting in the evaporator, liquid butane arrives from the condenser/absorber (component 6). In the evaporator (component 1), the partial pressure above the butane is greatly reduced by ammonia vapor flowing from the generator (component 29). With its partial pressure reduced, the butane evaporates near the saturation temperature of its partial pressure and cools itself, the ammonia, and the surroundings. The ammonia-butane vapor mixture leaves the evaporator and enters the pre-cooler (component 5) where it cools the hot vapor ammonia counter flowing from the generator. The now superheated ammonia-butane mixture flows out of the pre-cooler into the condenser/absorber which is being continuously cooled by the environment. Meanwhile, liquid water from the generator is sprayed into the condenser/absorber (35). With its great affinity for ammonia vapor, this sprayed water absorbs the vapor ammonia from the ammonia-butane mixture. This absorption of the ammonia vapor increases the partial pressure on the butane vapor to nearly the total pressure, allowing it now to condense at butane's saturation temperature for the total pressure (higher than butane's saturation temperature at the partial pressure of the evaporator). The butane and the ammonia water separate due to their respective density differences and the fact that ammonia-water is immiscible with butane at the condenser/absorber's temperature and pressure. Since liquid butane is less dense than liquid ammonia-water, it is the top liquid and is siphoned back to the evaporator. Meanwhile, the ammonia-water mixture leaves from the bottom of the condenser/absorber (27) and enters the solution heat exchanger (component 28). Here, the mixture is pre-heated before entering the generator (component 29).

Inside the generator, heat is applied to the strong ammonia-water solution driving off ammonia vapor where it rises under the influence of pressure created by the liquid head, h1, and is carried to the evaporator (1). The remaining weak ammonia-water solution is pumped up to a reservoir (component 35) via a bubble pump (component 36). In the reservoir, any residual ammonia vapor from the bubble pump is sent to the condenser/absorber. The weak ammonia water solution falls to the solution heat exchanger where it gives up its heat to the strong ammonia-water solution leaving the condenser. Finally, the water is sprayed into the condenser/absorber (35).

While the overall pressure of the cycle is constant, there are slight pressure variations within the cycle necessary for fluid motion. These are due to height variations and are not large enough to significantly affect property evaluation.
« Последна редакция: Юни 18, 2010, 01:31:06 am от altium »